April 29, 2024, 08:53 PM | #1 |
Senior Member
Join Date: December 8, 2015
Posts: 213
|
Rust Repair
Picked up a Smith 28 highway patrolman. Best double action trigger I have ever squeezed. But it has some rust. Tip of the barrel and edges of the cylinder were worn by the holster and then left to rust.
Don't need it to be perfect by any means, mainly just want to protect it. Lightly sand/buff the rust off and then what? Suggestions? |
April 29, 2024, 10:05 PM | #2 |
Staff
Join Date: November 2, 1998
Location: Colorado
Posts: 21,862
|
Don't sand or buff. You'll remove some of the bluing if you do.
Use a five cent piece and coconut oil (the active ingredient in Frog Lube is coconut oil). Scrape the rust off. You can use RIG gungrease on the end of the barrel afterward. If there's pitting and it bothers you, you'll have to have it refinished and reblued.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe! |
April 29, 2024, 10:21 PM | #3 |
Senior Member
Join Date: April 7, 2006
Posts: 10,991
|
If you use cold blue on it, don't expect it to protect the area-it won't.
|
April 30, 2024, 10:07 AM | #4 |
Senior Member
Join Date: December 8, 2015
Posts: 213
|
It doesn't bother me, I just want to stop it from rusting more than it is.
|
April 30, 2024, 04:20 PM | #5 |
Staff
Join Date: March 4, 2005
Location: Ohio
Posts: 21,099
|
Another approach is to buy some Gunzilla. It's made from vegetable oils, and it slowly debonds rust from steel. I've taken a small vial of it and set a small rusty tool in it. After a week or two, all the rust is lying on the bottom of the vial. Another time, I wet the rust-pitted bore of a rifle with it and let it sit in a gun vice for six weeks (I was away on business) before running a clean patch through. All the rust, as well as hard carbon mixed with it, came out with the first patch. It was all on one side of that patch, indicating it had not only debonded the rust and carbon but it had all slid to the bottom side of the barrel. My borescope showed nothing was left but bare steel, albeit there were pits where the rust had previously been. In your shoes, since Gunzilla is a finish-safe gun cleaner, I would wet the gun with it, especially on the rusty places, and put it in a plastic bag to prevent drying for a couple of weeks, take it out, and gently wipe the rust off with a rag. Repeat as needed.
Regarding Bill's mention of cold blues, some of them actually seem to activate metal and cause rust. I once had a handful of those little plastic colored yard flags used by the utility companies to mark buried cables and pipes. the "pole" on the flag is a length of carbon steel music wire. I cleaned and degreased the wires and dipped each one in a different cold blue and cold blacking solutions, rinsed them off, wiped them, and let them sit out overhanging the edge of a box so they were exposed to air on all sides of the bluing. After a couple of weeks, they all had rust blooms on them except the two that had been colored by Oxpho-blue and Van's Gun Blue. They remained rust-free. The difference between those two is they are both phosphoric acid-based, while the others are nitric or hydrochloric acid-based. Phosphoric acid solutions phosphatize the surface slightly, so they give you a little bit of preservative effect. I wouldn't count on it without soaking the finished and dried work in water-displacing oil followed by regular gun oil. Oxpho blue is the darker of those two brands, IME. Neither is as dark as something like Brownells 44-40 blue, but it causes the after-rust problem if you don't take care to neutralize it and get the nitric acid traces truely gone.
__________________
Gunsite Orange Hat Family Member CMP Certified GSM Master Instructor NRA Certified Rifle Instructor NRA Benefactor Member and Golden Eagle |
May 1, 2024, 12:32 AM | #6 |
Senior Member
Join Date: December 8, 2015
Posts: 213
|
Used a nickel as suggested (why a nickel?) and gently scraped the rust off. Rust came right off and I oiled it up and you can't even tell unless you really look for it. Good enough for me.
Still can't get over how good the trigger is. Nothing quite like a quality revolver from back in the day. |
May 1, 2024, 10:01 AM | #7 |
Staff
Join Date: November 2, 1998
Location: Colorado
Posts: 21,862
|
Brownells has a video I just received today:
https://www.brownells.com/the-trigge...qt_remove-rust He uses 0000 steel wool which does remove rust, but will affect the blue. That's why I use coconut oil and a nickel or even a copper penny. Penny or brass will leave marks, but they can be removed with gun solvent.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe! |
|
|