|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
May 15, 2024, 07:52 AM | #1 | |
Senior Member
Join Date: March 2, 2014
Posts: 12,004
|
mysteries of 22lr--part 3
While looking through my spare barrels rack I came across a Lilja 9 twist 22lr match chambered barrel I ordered years ago when I had embarked on a fantasy of loading my own high BC solid bullets and shooting long range.
That fantasy went down in flames as an abject failure; whenever I got into higher pressure territories the cases would often blow out--mostly because the firing pin was impacting right next to the relief slot cut out for the extractor, and the match chamber's tighter dimensions allowed pressure peaks to easily exceed what otherwise would be OK in a conventional chamber. Even when doing lower pressure loads, the results were hardly competitive with patterns I get from my 12 gauge shotgun. The barrel was not cheap, and I decided to give it one last attempt before mounting it on my wall of shame (which has lots of trophies on it). I decided to load up CU's smallest 32 grain solids which they say should work well in conventional 16 and 14 twist (I previously had tried all of the projectile weights) and not get greedy, just try an average load. Same result, a very wide pattern (shooting at 153 yds). Some of the dispersion was due to shooting in windy conditions as it was blowing 15 mph in a crossing tailwind, but I'm talking like dispersion of 12." That was it, it was time to yank the barrel and scuttle it once and for all. I just so happened to have a spare box of Tenex in my range bag and decided to see how badly it shot compared to the solids. I shot two 5 shot groups side-by-side though I couldn't see where the shots were landing through the scope. When I walked to the target I couldn't believe what I saw--the first group was under MOA and the second was right at MOA. What the heck? how is it possible this stuff shoots so much better than the solids--which is what the barrel is for at faster twist? And shouldn't the faster twist result in reduced performance of conventional close-to subsonic lead bullets? My other CZ jaguar is extremely accurate (by my standards, anyway) but only when I shoot in near-calm conditions, I would never waste premium ammo long-distance shooting in any kind of winds over 7 mph or so. Is it possible the faster twist actually helps improve performance and maybe even wind-bucking a bit of conventional lead 22lr ammo? I did a bit of googling for net wisdom and I'm not the only one who has encountered this counter-intuitive phenomenon. I found this on Sniper's Hide and it might give a second lease on life for my barrel--or at least a new fantasy for me to indulge in. Quote:
__________________
"Everyone speaks gun."--Robert O'Neill I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk! Last edited by stagpanther; May 15, 2024 at 08:10 AM. |
|
May 15, 2024, 10:33 AM | #2 |
Senior Member
Join Date: September 28, 2013
Posts: 3,951
|
Elegant rifle! 1moa at 100yd? That's very good. The best I could do, with barrel tuning and all, is 1.2-1.5moa. Hey, if it works, it works, fast twist or not.
-TL Sent from my SM-N960U using Tapatalk |
May 15, 2024, 05:26 PM | #3 |
Senior Member
Join Date: March 2, 2014
Posts: 12,004
|
New problem--the production lead bullet ammo--because it's generally lathered with goo of some sort--often leaves the case stuck in the match chamber after firing--especially Lapua's. Bummer, I thought I finally had discovered the barrel's true calling. The least likely to get stuck is Eley's.
__________________
"Everyone speaks gun."--Robert O'Neill I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk! |
May 15, 2024, 08:40 PM | #4 |
Senior Member
Join Date: September 28, 2013
Posts: 3,951
|
Try putting some lube on the casing. 22lr came in grease / wax in the old days.
Perhaps the extractor can use some refitting. My marlin used to do that. I refitted the extractor for better engagement angle and sping-out. -TL Sent from my SM-N960U using Tapatalk Last edited by tangolima; May 15, 2024 at 09:56 PM. |
May 15, 2024, 10:58 PM | #5 | |
Senior Member
Join Date: August 25, 2008
Location: In the valley above the plain
Posts: 13,473
|
Interesting results.
My son's new Kidd barrel won't extract unfired Eley or Wolf. Must be fire or manually extracted. (If you shoot much .22 LR, as those of us responding so far do, you need this tool: https://aandjsporting.com/the-extractor/) Was a bit of a burden in our last national level match, where *any* shot fired off the clock was an ND and match DQ. The classic was not allowed, "I've got a live one chambered, I'm gonna send it." Had to ask permission on every stage where he timed out with a live round chambered - or, when we were unable to ask for whatever reason(s), use the above linked tool (which is great). My Marlin 880SS has a rough chamber. Once the machine marks get filled in with wax, it doesn't like to extract anything. I've optimized the extractor as much as I can, but the roughness of the chamber trumps it. I need to fix that. Quote:
__________________
Don't even try it. It's even worse than the internet would lead you to believe. |
|
May 16, 2024, 01:30 AM | #6 |
Senior Member
Join Date: March 2, 2014
Posts: 12,004
|
It seems to be a problem more likely to happen with tight match chambers; what I think is going on is with successive cycling and firing more lubricant gets deposited on the chamber walls increasing the likelihood of the case jamming. I think case rim design might have something to do with it as well since the Eley ammo I used did not leave cases in the chamber and the others did; especially Lapua's, which is a huge disappointment since I just started using Lapua's better stuff. Thanks for the tool reference--I was thinking of making something like that myself since I don't like inserting a ramrod down the barrel a la muzzle loader to get the case out. I don't know about other rimfires--but the CZ bolt's and chamber face topology on the CZ has the slot for the extractor right next to where the firing pin impacts--which I consider a bad design feature since that creates a spot of weakness for higher pressures and also deforms the rim upon firing pin impact. This generally is not an issue with CZ's own larger dimension chambers, but with the tighter chamber on my Lilja it is.
__________________
"Everyone speaks gun."--Robert O'Neill I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk! Last edited by stagpanther; May 16, 2024 at 01:39 AM. |
May 16, 2024, 08:01 AM | #7 |
Staff
Join Date: July 28, 2010
Location: Arkansas
Posts: 8,826
|
I haven't been around here much lately, and I missed what kind of rifle that is. I'd love to know (hint, hint). I, too, am exploring the mysteries of .22LR. I'm just not as far down that road as you.
__________________
I'm a lawyer, but I'm not your lawyer. If you need some honest-to-goodness legal advice, go buy some. |
May 16, 2024, 08:46 AM | #8 |
Senior Member
Join Date: March 2, 2014
Posts: 12,004
|
I have two CZ 457 actions--one which I retained the CZ barrel--my Jaguar--and this one which I put a Lilja barrel match-chamber fast twist barrel on. Although it shoots well--it has its quirks which make for annoying stop-and-go shooting to clear cases with some ammo. I put both actions into KRG Bravo chassis and did yo-Dave spring jobs on them--I find that it is essential to get the triggerpull under 1 lb for long range precision work. You can easily sink as much money into a precision 22lr rig--if not more--than in a conventional larger caliber bolt rifle. To me the CZ is a reasonable start point in keeping costs down compared to a real custom rifle; sorta like the Savage actions of the rimfire world to me. But increasingly manufacturers like Kidd and Vudoo are offering complete custom builds that are very cost-competitive to a "do-it-yourself" build--and in the 22lr world the pressure for real performance is extreme--great for the shooters. Me personally 22lr shooting is an essential skill-building base for all other types of shooting that I do (not saying that I have necessarily gotten any better at any type of shooting, LOL).
__________________
"Everyone speaks gun."--Robert O'Neill I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk! |
May 16, 2024, 10:02 AM | #9 | |
Staff
Join Date: July 28, 2010
Location: Arkansas
Posts: 8,826
|
Quote:
__________________
I'm a lawyer, but I'm not your lawyer. If you need some honest-to-goodness legal advice, go buy some. |
|
May 16, 2024, 12:57 PM | #10 |
Senior Member
Join Date: March 2, 2014
Posts: 12,004
|
Got really deep in the weeds this morning after shooting some fairly wide groups in the 2 MOA or so range at 153 yds and discovered some revealing things about this particular barrel and ammo used in it.
Taking a bore scope look I discovered there tended to be a heavy lead abrasion deposit at the head of the throat after shooting--much more so than I see in my regular non-Bentz chambered barrels. This morning I decided to see what difference it would make single hand-feeding, Tenex was the easiest but still was a tight fit--I had to get the cartridge as straight aligned as I could prior to closing the bolt. Lapua exact and RWS 100--which are outstanding performers in my other barrels were so tight I'm guessing lead is possibly being shaved off the bullet as it enters the chamber. Neither of those two got accuracy results approaching that of Tenex. I don't think it's because Tenex is better ammo than the other two--it likely is that it simply has a slightly better fit to the chamber. It also is the only one of three ammos that doesn't leave the case in the chamber when extracting the brass after the shot. Because the magazine presents the bullets at an angle, I also think it is quite likely the bullets are being deformed at the chamber face when going into battery from the magazine. Tenex clearly bested the other ammos repeatedly, turning in one especially nice group of the 3 groups I shot.
__________________
"Everyone speaks gun."--Robert O'Neill I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk! |
May 17, 2024, 06:53 PM | #11 |
Senior Member
Join Date: March 2, 2014
Posts: 12,004
|
Winds dropped to near calm this evening and I grabbed the 22lr--I also was able to get a rare chance to shoot longer distance. I ended up at 239 yds. I didn't clean the bore from yesterday's shooting--maybe should have since only the first 5 shot group was pretty tight--the next two groups opened way up to to between 4 and 5 inches. The bolt got noticeably harder to close so I figure I fouled out.
__________________
"Everyone speaks gun."--Robert O'Neill I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk! Last edited by stagpanther; May 17, 2024 at 07:11 PM. |
June 2, 2024, 02:00 PM | #12 |
Senior Member
Join Date: March 2, 2014
Posts: 12,004
|
Quite windy today but I woke up jonesing for some 22lr activity. Decided to shorten the distance a bit to 126 yards thinking the less time in the air the greater the chances the high winds (10-20 gusty from the left) wouldn't totally blow the groups apart. I shot the best ammos I have, Lapua X-Act, RWS R100, Lapua Long Range and Eley Tenex; all out of my jaguar. The big surprise for me was that Lapua's Long range turned in the smallest group--I believe it is a subsonic. However, looking at the best 4 shots of Tenex (which grouped under .5 MOA) I would say it's entirely possible I pulled the shot throwing the group result. Out of my Lilja barrel (which has "issues" that I have not fully resolved) and my other 16" barrel CZ Tenex usually beats all comers out of them.
__________________
"Everyone speaks gun."--Robert O'Neill I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk! |
June 2, 2024, 03:53 PM | #13 |
Senior Member
Join Date: July 22, 2010
Location: Madison, Wisconsin
Posts: 1,309
|
It's better to wonder why a rifle shoots so well compared to wondering why it doesn't!
__________________
My book "The Pheasant Hunter's Action Adventure Cookbook" is now on Amazon. Tall tales, hunting tips, butchering from bird to the freezer, and recipes. |
June 2, 2024, 04:47 PM | #14 | |
Senior Member
Join Date: March 2, 2014
Posts: 12,004
|
Quote:
__________________
"Everyone speaks gun."--Robert O'Neill I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk! |
|
June 3, 2024, 01:33 AM | #15 |
Senior Member
Join Date: August 25, 2008
Location: In the valley above the plain
Posts: 13,473
|
I don't think your theory of instant headspace adjustment is valid, due to different breech face designs and types.
But it is an interesting one to think about. Especially since I (and several "high end" testers) have found the Springfield 2020R to have an erratic ignition problem, over other problems. (It has a coned chamber face and no rim support.)
__________________
Don't even try it. It's even worse than the internet would lead you to believe. |
June 3, 2024, 04:46 AM | #16 | |
Senior Member
Join Date: March 2, 2014
Posts: 12,004
|
Quote:
For example, it appears to me that a tight-tolerance match chambered 22lr barrel will almost certainly need to be custom configured to the ammunition being used in it because the variance between ammos is enough that the bullet will be potentially deformed in forcing it into the throat--not to mention the quick accumulation of lubricant, lead and residue complicating reliable firing and extraction. I have a top-rated match barrel which shall go nameless which whenever I look at the throat after using it the throat shows unequal lead build-up, always in the same area, which I believe the very tight tolerance might possibly magnify slight variances in concentricity as the bullet is conformed to the throat. I won't even get into the dance of barrel and bolt shims--which when you think about it is really just another form of adjustable headspace. Of course my concept of adjustable headspace is a bit of fantasyland speculation and I don't know how that could be executed in a quick and precise manner--but I've seen enough variation in my shooting experience to see what I believe is a real problem--and opportunity--to improve upon 22lr consistency in a wider range of uses. I have to admit that I personally am not really interested in 100 yards or less shooting since that arena has already been fully mastered--it's shooting beyond 100 yards that really interests me cause it's more fun. I've also noticed that the problem is further complicated by the performances of ammunition when the variables of barrel length and distances fired at are brought into the equation. As always--I'm no expert and could be totally wrong--but I still like to think about it. And another thing... I've found that in a tight match chamber that tends to hang up on certain cases after firing and the bolt fails to extract them--waiting 10 to 20 seconds before attempting to extract usually succeeds in getting them out. I'm wondering if there is further contraction of the case as it cools in the chamber after initial "snap-back"?
__________________
"Everyone speaks gun."--Robert O'Neill I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk! Last edited by stagpanther; June 3, 2024 at 05:03 AM. |
|
June 3, 2024, 09:57 AM | #17 |
Senior Member
Join Date: September 28, 2013
Posts: 3,951
|
Barrel tuner perhaps?
-TL Sent from my SM-N960U using Tapatalk |
June 3, 2024, 10:01 AM | #18 | |
Senior Member
Join Date: March 2, 2014
Posts: 12,004
|
Quote:
__________________
"Everyone speaks gun."--Robert O'Neill I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk! |
|
June 3, 2024, 10:26 AM | #19 | |
Senior Member
Join Date: September 28, 2013
Posts: 3,951
|
Quote:
I'm too cheap to have my rifle threaded, so I make tuner out of different things. The latest version is hose clamp from home Depot. I need to move its position on the barrel in very small steps, 0.01", so I took calipers to the range. It works for me. I don't change it on the fly till I change ammo, or between summer and winter perhaps. Actually self-adjust headspacing for rimfire does exist. It is the direct blow back action in semi auto. For bolt actions, shimming may be an option. -TL Sent from my SM-N960U using Tapatalk Last edited by tangolima; June 3, 2024 at 10:36 AM. |
|
June 3, 2024, 12:20 PM | #20 |
Senior Member
Join Date: February 22, 2008
Location: SW Washington state
Posts: 2,033
|
Very likely IMO
It's just logical the case would cool more quickly than the chamber, very little mass, plus it has sprung back from the chamber wall very slightly further allowing it to cool more quickly than steel. You are likely finding a "sweet spot" in that 15-20 secs? that permits extraction.
__________________
ricklin Freedom is not free |
June 3, 2024, 12:22 PM | #21 | |
Senior Member
Join Date: March 2, 2014
Posts: 12,004
|
Quote:
__________________
"Everyone speaks gun."--Robert O'Neill I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk! |
|
June 8, 2024, 07:50 PM | #22 |
Senior Member
Join Date: March 2, 2014
Posts: 12,004
|
Fresh batch of Tenex and Eley Match came in today--so I was pretty eager to try them out in my CZ 457 Jaguar. Problem is I had taken the Leupold HD5 off to do duty elsewhere, so I elected to mount one of my SWFA 20 fixed mag scopes on and get it dialed in. For some reason, late evening or whatever, the image at longer distance around 175 yds was washed out and I couldn't see the target well so I moved it closer to 79 yds where the sight picture was much clearer. Decided to make a fun challenge out of it--so I decided on 11 shot groups of each of my premium type ammos.
After getting on target--my first group was the tenex and as I expected it did pretty well. After that followed Lapua X-act--which kinda did poorly compared to what I expected, coming in around 1.25 MOA--as did RWS 100 and Eley Match. Last up as it started getting dark was Lapua Long Range, which I expected would come in a little worse that X act--but instead turned in this stunner which totally took me by surprise: You might notice that it consists of only 10 shots and there are suspicious impacts nearby that would have widen the group significantly. Perfectly good explanation (excuse)-- just as I was about to finish a truck came in to dump stuff and I had to stop and move, I couldn't "find the groove" that I had been shooting after starting again--so I decided to dismiss the first errant shot and give myself a bonus attempt which also went wide. That's when I decided to award myself the handicap deduction of the two shots under "shootus interruptus."
__________________
"Everyone speaks gun."--Robert O'Neill I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk! Last edited by stagpanther; June 8, 2024 at 08:04 PM. |
June 9, 2024, 12:40 AM | #23 |
Senior Member
Join Date: July 14, 2023
Location: down town USA
Posts: 294
|
i was just thinking about the head-space question and had a novel idea. what about building a bolt that has spring tention to keep it tight against the cartridge? it would only need a few thousandths and not strong pressure... what think ye ?
that's my idea, now go paton it. |
June 9, 2024, 03:00 AM | #24 | |
Senior Member
Join Date: March 2, 2014
Posts: 12,004
|
Quote:
__________________
"Everyone speaks gun."--Robert O'Neill I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk! Last edited by stagpanther; June 9, 2024 at 03:07 AM. |
|
|
|